全國服務熱線:

                          18396804865 錢經理

                          怎樣操縱數控切割機割嘴耗損過快

                          2019-11-08 16:46:32文章來源:www.labobinedelisette.com847

                          怎樣操縱數控切割機割嘴耗損過快
                          How to Manipulate CNC Cutting Machine Cutting Nozzle Loss Too Fast
                          數控切割機因為許多公司以便單純性的減少激光切割機生產成本,選購的割嘴品質較為拙劣,及其實際操作應用有誤,促使手持式數控機床等離子切割的割嘴在操作流程極易耗損,必須經常拆換。所以便攜式數控火焰切割機需要注意割嘴的選擇,可有效緩解割嘴損耗問題:
                          CNC cutting machine because many companies in order to simplify the production cost of laser cutting machine, the quality of the selected cutting nozzle is relatively poor, and its actual operation application is wrong, so that the plasma cutting nozzle of hand-held CNC machine tool is very easy to wear out in the operation process, and must be often replaced. Therefore, portable numerical control flame cutting machine needs to pay attention to the choice of cutting nozzle, which can effectively alleviate the problem of cutting nozzle loss:
                          挑選適合的割嘴應依據激光切割鋼件的薄厚,挑選適合的割嘴。裝配線割嘴時,務必使內嘴和外嘴維持共同,以確保激光切割氧水射流坐落于加熱火苗的管理中心,安裝割嘴時留意扭緊割嘴螺帽。
                          Selection of suitable cutting nozzle should be based on the thickness of laser cutting steel, select the appropriate cutting nozzle. When cutting nozzle in assembly line, it is necessary to keep the inner nozzle and the outer nozzle together to ensure that the oxygen-water jet of laser cutting is located in the management center of heating flames. When installing the cutting nozzle, pay attention to tightening the nut of the cutting nozzle.
                          割嘴頭和割炬相互配合關不緊的解決打火后火苗雖一切正常,但開啟激光切割氧調節閥門時,火苗就馬上吹滅。其緣故是割嘴頭和割炬配,合面關不緊。這時應將割嘴扭緊,失效時要拆下來割嘴,用水砂紙輕輕地。碾磨割嘴頭相互配合面,直至相互配合嚴實。
                          The problem that the cutting nozzle and torch are not tightly connected with each other can be solved. After the ignition, the flame will blow out immediately when the laser cutting oxygen regulating valve is opened. The reason is that the cutting head and torch are matched, and the joint is not tight. At this time, the cutting nozzle should be tightened. When it fails, the cutting nozzle should be removed and gently sanded with water. Grinding and cutting nozzles to cooperate with each other until they cooperate tightly with each other.
                          淬火的解決當產生淬火時,應先關掉激光切割氧調節閥門,隨后關掉乙炔氣體調節閥門及加熱氧調節閥門。在一切正常工作中終止時,先要關激光切割氧調節閥門,再關乙炔氣體和加熱氧調節閥門激光切割機。
                          When quenching occurs, the laser cutting oxygen regulating valve should be turned off first, then the acetylene gas regulating valve and the heating oxygen regulating valve should be turned off. When all normal work is terminated, the laser cutting oxygen regulating valve should be turned off first, then the laser cutting machine of acetylene gas and heating oxygen regulating valve should be turned off.
                          維持割嘴安全通道清理割嘴安全通道應常常清潔光潔,孔洞內的廢棄物應隨時隨地用通針消除整潔。
                          Maintaining the safe passage of the cutting nozzle to clean the safe passage of the cutting nozzle should always be clean and clean, and the waste in the hole should be removed at any time and anywhere with a needle.
                          清除鋼件表層鋼件表層的厚銹、水和油廢棄物要清除掉。在混凝土地面上激光切割時要木架鋼件,以防銹處理皮和爐渣在混凝土地面上爆濺致死。
                          The thick rust, water and oil waste on the surface of steel parts should be removed. When laser cutting on concrete floor, wooden frame steel pieces should be used to prevent rust treatment skin and slag from splashing on concrete floor.
                          查驗射吸狀況射吸式割炬經射吸狀況查驗一切正常后,即可把乙炔氣體皮管接好,以不漏汽并非常容易插上、拔掉為標準。應用等壓式割炬時,應確保乙炔氣體有必須的壓力。
                          After checking the ejection and suction conditions, the ejection and suction torch can connect the acetylene gas pipes well after checking the ejection and suction conditions. The standard is that no leakage is very easy to plug in and pull out. When applying isobaric cutting torch, the necessary pressure of acetylene gas should be ensured.
                          數控切割機火焰熄滅的處理點火后,當擰預熱氧調節閥調整火焰時,若火焰立即熄滅,其原因是各氣體通道內存有臟物或射吸管喇叭口接觸不嚴,以及割嘴外套與內嘴配合不當。此時,應將射吸管螺母擰緊;無效時,應拆下射吸管,清除各氣體通道內的臟物及調整割嘴外套與內套間隙,并擰緊數控切割機。
                          When the flame of NC cutting machine is extinguished after ignition, if the flame is extinguished immediately when the preheated oxygen regulating valve is twisted to adjust the flame, the reason is that there are dirt in each gas passage or the horn mouth of the ejector suction pipe does not contact tightly, and the outer jacket of the cutting nozzle does not match with the inner nozzle properly.  At this time, the ejector and suction nut should be tightened; when ineffective, the ejector and suction pipe should be removed, dirt in each gas passage should be removed, clearance between the jacket and the inner jacket of the cutting nozzle should be adjusted, and the numerical control cutting machine should be tightened.
                          http://www.labobinedelisette.com/

                            濟南卓然天成是大型數控火焰切割機廠家,數控等離子切割機廠家,便攜式數控切割機廠家www.labobinedelisette.com,供應河北數控火焰切割機,山西數控等離子切割機,遼寧便攜式數控切割機,吉林數控火焰切割機,黑龍江數控等離子切割機,江蘇數控切割機,浙江數控切割機,安徽數控切割機,福建切割機,江西切割機,山東數控切割機,臺灣切割機,河南切割機,湖北數控切割機,湖南數控切割機,廣東切割機,海南數控切割機,四川數控切割機,貴州數控切割機,云南切割機,陜西切割機,甘肅數控切割機,青海數控切割機,需要的朋友聯系我們15254176866

                          電話咨詢
                          郵件咨詢
                          在線地圖
                          QQ客服
                          網站地圖 好多水好爽小荡货好紧好热